Sometimes you are looking at a screenful of text, and only part of the
current paragraph you are reading is visible on the screen. The
commands detailed in this section are used to shift which part of the
current node is visible on the screen.
SPC (scroll-forward)
NEXT
Shift the text in this window up. That is, show more of the node which
is currently below the bottom of the window. With a numeric argument,
show that many more lines at the bottom of the window; a numeric
argument of 4 would shift all of the text in the window up 4 lines
(discarding the top 4 lines), and show you four new lines at the bottom
of the window. Without a numeric argument, SPC takes the bottom
two lines of the window and places them at the top of the window,
redisplaying almost a completely new screenful of lines. If you are at
the end of a node, SPC takes you to the “next” node, so that you can
read an entire manual from start to finish by repeating SPC.
The NEXT key is known as the PageDown key on some
keyboards.
C-v (scroll-forward-page-only)
Shift the text in this window up. This is identical to the SPC
operation above, except that it never scrolls beyond the end of the
current node.
M-x scroll-forward-page-only-set-window
Scroll forward, like with C-v, but if a numeric argument is
specified, it becomes the default scroll size for subsequent
scroll-forward and scroll-backward commands and their
ilk.
DEL (scroll-backward)
PREVIOUS
Shift the text in this window down. The inverse of
scroll-forward.
If you are at the start of a node, DEL takes you to the
“previous” node, so that you can read an entire manual from finish to
start by repeating DEL. The default scroll size can be changed by
invoking the (scroll-backward-page-only-set-window) command with
a numeric argument.
If your keyboard lacks the DEL key, look for a key called
BS, or ‘Backspace’, sometimes designated with an arrow which
points to the left, which should perform the same function.
The PREVIOUS key is the PageUp key on many keyboards. Emacs
refers to it by the name PRIOR.
M-v (scroll-backward-page-only)
Shift the text in this window down. The inverse of
scroll-forward-page-only. Does not scroll beyond the start of
the current node. The default scroll size can be changed by invoking
the scroll-backward-page-only-set-window command with a numeric
argument.
M-x scroll-backward-page-only-set-window
Scroll backward, like with M-v, but if a numeric argument is
specified, it becomes the default scroll size for subsequent
scroll-forward and scroll-backward commands.
M-x down-line
Scroll forward by one line. With a numeric argument, scroll forward
that many lines.
M-x up-line
Scroll backward one line. With a numeric argument, scroll backward that
many lines.
M-x scroll-half-screen-down
Scroll forward by half of the screen size. With a numeric argument,
scroll that many lines. If an argument is specified, it becomes the new
default number of lines to scroll for subsequent
scroll-half-screen-down and scroll-half-screen-up commands.
M-x scroll-half-screen-up
Scroll back by half of the screen size. With a numeric argument,
scroll that many lines. If an argument is specified, it becomes the new
default number of lines to scroll for subsequent
scroll-half-screen-down and scroll-half-screen-up
commands.
The scroll-forward and scroll-backward commands can also
move forward and backward through the node structure of the file. If
you press SPC while viewing the end of a node, or DEL while
viewing the beginning of a node, what happens is controlled by the
variable scroll-behavior (see scroll-behavior).
The scroll-forward-page-only and scroll-backward-page-only
commands never scroll beyond the current node.
C-l (redraw-display)
Redraw the display from scratch, or shift the line containing the cursor
to a specified location. With no numeric argument, ‘C-l’ clears
the screen, and then redraws its entire contents. Given a numeric
argument of n, the line containing the cursor is shifted so that
it is on the nth line of the window.
C-x w (toggle-wrap)
Toggles the state of line wrapping in the current window. Normally,
lines which are longer than the screen width wrap, i.e., they are
continued on the next line. Lines which wrap have a ‘\’ appearing
in the rightmost column of the screen. You can cause such lines to be
terminated at the rightmost column by changing the state of line
wrapping in the window with C-x w. When a line which needs more
space than one screen width to display is displayed, a ‘$’ appears
in the rightmost column of the screen, and the remainder of the line is
invisible. When long lines are truncated, the mode line displays the
‘$’ character near its left edge.